RISOL®
RISOL®
With Risol® you can achieve a strength class of up to CT-C30-F5 and can heat up after just the 4th day. Your optimum decision for a higher screed quality and optimum processing.
Compressive and flexural strength
up to CT-C30-F5Foot traffic
after 1 dayNormal site traffic
after 3 daysCommisioning UFH
after 4 daysMinimum nominal thickness 2 kN/m²
from 35 mmSurface strength
≥ 1,0 N/mm²Shrinkage
SW 2Energy efficiency class
up to EC 2Certification
DGNB conformity, emission-tested (TÜV Rheinland), EC1 Plus according to Emicode
Dosage & Cement quantity
MIXING INSTRUCTIONS
Notes
POINT LOADS INFORMATIONS
AREAS OF APPLICATION
Downloads
Dosage
|
MIXING INSTRUCTIONS
- Shake the container well to mix the Risol® additive to a consistent colour before use, and then shake as required throughout the installation to maintain the consistency of the liquid (every 30 mins).
- Fill half of mixing vessel with 0-4 mm screeding sand and required cement.
- Add Risol® to the first mixing water (usually 5-10 litres), then fill the machine completely.
- Gradually add the required amount of residual water until a stiff-plastic consistency is achieved.
- Let the screed mix for a full 2 minutes.
SAND, WATER, CEMENT
- Grading curve: Sand must be according to DIN 1045-2 A/B /BS 13139*, for the production of screed concrete, grain size range 0-4 mm
- W/C value: Min 0,4, max. 0,6
- Cement: Use of cement according to the PCT cement release list
*UK only
PROCESSING INSTRUCTIONS
- Working time: 60 minutes
- Finishing time: 90 minutes
- Outside temperature: +5 °C to +28 °C for screed, environment and substrate
- Do not mix with other screed additives
- Never reactivate screed that has already set with water
Airing
- If the air humidity is 55 % or higher, ventilate 3-4 times a day for 20-30 minutes 24 hours after screed installation in order to achieve readiness for covering.
- If the humidity is below 55%, contact PCT technical support to avoid cupping etc.
FURTHER PRODUCT FEATURES
- Tension and shrinkage reduced according to SW 2
- Density approx. 2,000 to 2,200 kg/m3
- Thermal conductivity approx. 1.5-2.4 lambda
- Better processing and lower peel resistance
- Reduction of air content
- Start ventilation after 1 day
Protective instructions during and after installation
- We recommend our PROTEC-ES/SP product to protect against drying out too quickly, depending on the floor covering. We recommend consulting the PCT technical support team.
- Protect the screed against rapid drying of the surface due to draughts, sunlight and low humidity.
- Large window fronts and floor-level glass façade areas should be darkened if necessary.
- Cover screeds in outdoor areas or enclose areas to be covered. Contact PCT technical support if screed is to be laid outdoors.
CM MEASUREMENT
- A screed with Risol® does not have a defined readiness for covering and is therefore assessed with regard to its residual moisture in accordance with the measurement and assessment standards of DIN 18560/BS 8204*.
- In this case, PCT Chemie and the Retanol® specialist company assume no responsibility for the readiness for covering.
- The CM measurement is therefore part of the floor layer's inspection obligation and is carried out by him.
*UK only
POINT LOADS INFORMATIONS
| Area load Point load | 2,0 kN/m2 1,0 kN | 3,0 kN/m2 2,0 kN | 4,0 kN/m2 3,0 kN | 5,0 kN/m2 4,0 kN | 7,5 kN/m2 6,0 kN | 10,0 kN/m2 8,0 kN |
| Flexuale strength ≥ F4 | 40 mm | 50 mm | 55 mm | 60 mm | n/a | n/a |
| Flexuale strength ≥ F5 | 35 mm | 45 mm | 50 mm | 55 mm | 75 mm | 90 mm |
- Unless otherwise defined, data as minimum nominal thickness (without UFH) or minimum pipe cover (with UFH).
AREAS OF APPLICATION
- For all screeds according to DIN 18560, part 1–7, BS 13892*/BS 8204*
- Particularly suitable for high-strength screeds with a fast readiness for covering
- Screed are suitable for indoor and outdoor areas as well as in permanently wet areas
*UK only
Dosage & Cement quantity
Dosage
|
MIXING INSTRUCTIONS
Notes
POINT LOADS INFORMATIONS
AREAS OF APPLICATION
Downloads